Peninsula Daily News Crime, How To Get Millions Of Coins In Madden 22, Brian Kim, Cpa Clearvalue Tax Net Worth, Articles S

The activation of a new operating mode is not possible, the error code is sent as the response to the activation command. o 8005 Program automatic start active. Drive is in operating state Fault or Fault Reaction Active. Undervoltage in internal eSM power supply. No analog reference value source selected. Limit switch or reference switch signal not defined for signal input function. Reference switch or limit switch not connected correctly or supply voltage for switches too low. - Short circuit at connector or encoder cable. The scaling factors for position, velocity or acceleration/deceleration are beyond internal calculation limits. We empower all to make the most of their energy and resources, ensuring Life Is On everywhere, for everyone, at every moment. If the winding voltage of the motor is lower than the nominal supply voltage of the drive, this may result in motor overtemperature due to high current ripple. The address of the parameter that caused the detected error can be read via the parameter _PAR_ScalingError. Improve the heat dissipation in the control cabinet. Wait for Autotuning to finish before changing the parameter. Overflow error detected during encoder scaling. The motor shaft may have been moved while the drive was powered down. The velocity was set to a value greater than the maximum permissible velocity in parameter CTRL_v_max or M_n_max, whichever is lower. Two cycles have passed without a synchronization signal having been received. Speed limit for machine operating mode Setup Mode must not be greater than speed limit for machine operating mode Automatic Mode. eSM module: System error detected: 3_3V overvoltage. The encoder does not support motor temperature monitoring. Wait until the motor has come to a standstill (x_end = 1). Power supply outage, insufficient power supply. Configuration error detected: Invalid BISS encoder parameter setting. D6: Sine/cosine inputs below LOS threshold. Code 8503 / external diag. The password that was sent by the configuration tool is not identical to the password stored in the device. Code 8503 / external diag. System error detected: Motor encoder (Hiperface), System error detected: Motor encoder initialization. Easily find the nearest Schneider Electric distributor in your location. If you are still getting the CFF fault then you will need to replace the drive. eSM module: System error detected: 3_3V undervoltage. Direction-dependent SLS is active, but no speed limit greater than 0RPM has been specified in the parameter eSM_v_maxSetup or in parameter eSM_SLSnegDirS. System error detected. CPU_A and CPU_B have different position values. Analog encoder signals are subject to interference. o 8006 Program stopped. These limit switches are not assigned to inputs. Verify wiring and connected devices. Parameter AT_gain or AT_J are written during Autotuning. If the fault clears, now try and reprogram the drive. However, there is a 0 level the signal input. ?`wy:Zvv;c@8\t8n }DI-Ql'AD361)-BN> [7md$QQ)o0>Z9XOW; fa$f~8UI The write access level expert is required. Wait until ongoing offset positioning has finished. Motor encoder: Position evaluation error detected. Motor subjected to vibration or shock when stopped after activation of the switch signal. Now, you will be the first to know the updates from Schneider Electric. Resolution of scaling too high (range exceeded), Change for jerk filter input position too great. Fault detection codes that cannot be cleared automatically (continued), Enhancements made to version V1.2 in comparison to V1.1, Using the drive with motor having a different size, Use with a smaller rated motor or without a motor, Single-phase supply voltage: 100120 V 50/60 Hz, Single-phase supply voltage: 200240 V 50/60 Hz, Three-phase supply voltage: 200240 V 50/60 Hz, EMC mounting plate: size 1 VW3A9523, size 2 VW3A9524 or size 3 VW3A9525 to be ordered separately, ATV12H075F1, ATV12H075M2 AND ATV12H075M3 - GROUND CONTINUITY HAZARD, Access to the terminals if you use stripped wire cables, Access to the line supply terminals to connect ring terminals, HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH, M External reference value -400 to +400 Hz -, M Analog input virtual 0 to 100 % of HSP -, M External reference value -400 Hz to 400 Hz -, M Application Overload threshold 70 to 150% of nCr 90% of of nCr, M Time delay before automatic start for the underload fault, M Motor frequency threshold 0 to 400 Hz 50 or 60 Hz, M Motor current threshold 0 to 1.5 In (1) InV, M Motor thermal state threshold 0 to 118% of tHr 100%, M Automatic DC injection current 0 to 120% of nCr 70%, M Automatic DC injection time 0.1 to 30 s 0.5 s, M Low speed operating time 0.1 to 999.9 s nO, M PI feedback supervision function time delay 0 to 600 s 0 s, M Maximum frequency detection hysteresis 0 to HSP 0 Hz, M Time delay before automatic start for the overload fault, M Application Underload threshold 20 to 100% of nCr 60%, M Starting frequency of the auxiliary pump 0 to tFr HSP, M Time delay before starting the auxiliary pump, M Ramp for reaching the auxiliary pump nominal speed, M Auxiliary pump stopping frequency 0 to tFr 0 Hz, M Ramp for auxiliary pump stopping 0 to 999.9 s 2 s, M Zero flow detection activation threshold 0 to 400 Hz 0 Hz, M Zero flow detection offset 0 to 400 Hz 0 Hz, Single variable mode - 1 single variable speed pump, M Current limitation 0.25 to 1.5 In (1) 1.5 In, RISK OF DAMAGE TO THE MOTOR AND THE DRIVE, M Current limitation 2 0.25 to 1.5 In (1) 1.5 In, M Com scanner write address value 2 LFRD value, Assistance with maintenance, detected fault display.